• All digital design, with outputs for printer, computers, and LANs
• Rugged Membrane Face Plate
• Backward Compatibility with 630, 6300 Series
• Define-able Zone Names for easy to review printouts and logs

• At-A-Glance Viewing of Status of ALL Zones
• Plus Output Capabilities:
- Printer / Serial Ports, RS-232; RS-485
- Ethernet Connection Option
• Recessed Switches and Lights in Sealed Membrane Keypad
• Uses Existing Zone Wiring for 6300-24 Annunciators
• Optional Added Line Security using Dual Resistors
- 4 States: Trouble (Open) / Normal / Alarm / Trouble (Short)
• Annunciates Zone (door) Status and new Fault Status
- Even in Access Mode
• Logs Events to Printer and File
• Easy Programming
• Use Zone Names Feature for Better Printouts and Logs

UPGRADE EXISTING 630 AND 6300 SERIES

The new system provides more reporting and tamper monitoring, even in
access mode. Door status is displayed in both access and secure modes.
Line tampering is also reported in both modes.

WORK FROM THE INSTALLED BASE
Use the existing wires and sensors. To upgrade to the higher security, add a resistor to the existing sensors. More security with no new cabling required.

ALL EVENTS ARE RECORDED TO A PRINTER / DATA PORT

Size: 19”W x 5.25”H x 10”D ( 48.25 x 13.3 x 25.4 cm) (plus connectors); rack mount case
Power: 115 / 230 V, 50/60 Hz; internal voltage selector switch; onboard switching
regulated supply
Backup Battery: 12V, 4.5AH, lead acid gel type
Zone Inputs: 24 individual zones
Line Security:

 • Advanced Mode: 4 levels; Normal, Alarm, Trouble Short, Trouble Open

 • Classic Mode: 3 levels; Normal, Alarm Short, Alarm Open
Switches:
• Access/Secure: 24, one for each zone; Push button membrane switch; Push-Toggle
Access mode (yellow light ON) zone activity is not annunciated or recorded.
Secure mode (yellow light OFF) annunciates and records all events - alarm, restore,
silence, reset
• Test Switch: Tests all zones by simulating an imbalance on all input lines
• Silence Switch: Shuts off audible signal; red alarm light stay (memory mode)
• Reset Switch: Resets all zones; Clears red light (memory mode)
Indicators:
• Red Lights, 1 per zone: ON indicates an alarm condition; OFF indicates normal
condition
- Blinking light indicates un-silenced alarm
- Steady light indicates memory mode following silenced alarm, Reset clears
steady light
- Double Blinking light indicates a line trouble; trouble is reported in both Access and
Secure Modes
• Yellow Lights, 1 per zone: ON indicates a zone in Access Mode; OFF indicates zone
in Secure Mode
• Green Lights, AC and BATT:

- ON indicates OK

- BLINK indicates AC or Battery failure

- OFF indicates unit is off
Zone Inputs, 24:
• Base unit has 50 pin connector; compatible with 6300-24-DSR annunciators
• Easy upgrade to existing 6300 series annunciator installations:
simply add a 3.01K resistor across the N.C. contact
• Output board has cage clamp connector; may be remoted from panel, DIN mount
• Resistors: 2 per zone; 3.01 K ohm, 1%
- 3.01K = Normal; 6.02K = Alarm; Short = Trouble; Open = Trouble
Processor: 386 embedded micro; real time clock, DOS operating system
Ports:
• Terminal I/O Port (RS-485 option, future use)
• RS-232 Serial / Printer Port
• Network Interface (future use)
Fuses:
• AC Input 3 Amp
• Battery 3 Amp
Printer Output: Logs all events by zone and button push, with time, date.
• Alarms, Restorals reported for any zone in Secure Mode
• Line Trouble reported for any zone in Secure or Access Mode
• AC Fail, Battery Fail
• Pushing of Silence and Reset Buttons

Download Brochure